Special Features:

Frame:
The frame is made from close Grained cast iron with high molecular stability to ensure adequate strength, stiffness and rigidity at full load. In special cases the frame may be made of welded steel construction which is heavily ribbed and fully stress relieved, Thus the construction is compact and extremely rigid. All the frames are designed to eliminate undesirable distortion of the guiding surfaces, to guarantee accurate alignment of tooling.

Crank Shaft:
Crank shaft is made from high carbon normalised steel forging. It has large bearing surface for smooth running. The gun metal bushes 'fine finished to close tolerances' are provided for the Crank Shaft for running at high speed. The Cross SEctional area of the Crank pin is adequate to minimise the deflection and to provide an optimum factor of safety

Ram:
The ram is made of heavy duty cast iron and is accurately machined. The extra long cast iron guides are provided for stability and to eliminate the tendency to bind. The ball seat is smooth enough to match bearing surfaces. The ram has a round die stalk hole and clamp. The ram can be easily adjusted by screw on the sides.

Stroke:
Presses over 10 tons are manufactured with adjustable stroke. The adjustment is made by means of a sleeve with multiple claws. The presses may be operated for continuous stroke.

Brake:
Spring operated powerful heavy duty brakes of release type is provided. It works on Top dead centre at the end of continuous sequence.

Inclining Mechanism:
The Press may be inclined to a maximum of approximately 20 degree by jacking screws positioned at the rear between the sides. The inclining mechanism properly balances the load on both legs and keep the press sufficiently high above the floor for a man to operate it easily conveniently and safely, while in a standing position. The points of pivoting is so located that in all positions the working height of the press is not materially changed. .

Technical Specifications:
Specification of Power Presses (5 Thru. 100 Ton.) MODEL:-"C" Type

Sr. No.	SPEC.	Unit.	APP-5	APP-10	APP-15	APP-20	APP-30	APP-40	APP-60	APP-80	APP-100
1	Capacity at 20º Crank Angle before B.D.C. at Standard Stroke.	Ton	5	10	15	20	30	40	60	80	100
2	Stroke Fixed : Std.	MM	20	25	32	40	50	63	89	89	100
	Optional.	MM	25	20 32 40 50	25 40 50 63	32 50 63	32 40 50 63	40 50 80	32 50 63 75 100	63 75 100	75 89 100 125
3	Adjustability of Stroke.	MM	----	10-25	10-32	10-40	10-50	10-63	10-89	10-89	10-100
4	Depth of Throat.	MM	80	100	120	150	190	235	250	265	280
5	Length of Bed L-R.	MM	304	350	380	460	560	620	750	775	825
6	Width of Bed F-B.	MM	200	222	240	280	370	440	550	550	560
7	Hole in Ram for Tools Dia.	MM	25	30	32	35	38	45	51	55	55
8	Hole in Ram for Tools Depth.	MM	60	70	70	70	90	90	90	90	90
9	Maximum Distance between Bed and Ram at T.D.C. (Shut Height).	MM	140	170	200	240	270	300	340	360	375
10	Thickness of Bolster.	MM	50	60	65	65	70	75	110	130	150
11	Adjustability of Ram.	MM	50	60	65	65	75	75	75	80	80
12	Opening in Table (Bed) Dia.	MM	75	100	125	150	200	250	255	275	275
13	Flywheel Diameter: Geared.	MM	360	420	450	500	710	740	860	925	1003
	Ungeared.	MM	450	550	600	600	750	800	-----	-----	-----
14	Stroke per Minute: Geared.	MM	80	75	60	60	55	50	45	45	40
	Ungeared.	MM	150	130	120	115	110	-----	-----	-----	-----
15	Distance from Floor to Top of Bed.	MM	500	735	735	735	735	735	800	800	800
16	Capacity of Motor.	kW.	0.75	0.75	1.5	1.5	2.25	3.75	5.65	7.5	7.5
17	Speed of Motor: Geared.	R.P.M.	1440	1440	1440	1440	1440	1440	1440	1440	1440
	Ungeared.	R.P.M.	960	960	960	960	960	-----	-----	-----	-----
18	Type of Clutch.	Rolling key	Rolling key	Rolling key	Rolling key	Rolling key	Rolling key	Rolling key	Rolling key	Rolling key
19	Weight Approximate.	Kgs.	275	430	750	925	1600	2200	3500	4200	5200

NOTE:
(1) All product specification and features, as described or illustrated are subject to chang without notice. (2) Shut height at standard maximum stroke is the distance between table surface and face with slide at bottom of stroke and adjustment-up.